diff options
Diffstat (limited to 'man/aeroup.man.txt')
| -rw-r--r-- | man/aeroup.man.txt | 114 |
1 files changed, 42 insertions, 72 deletions
diff --git a/man/aeroup.man.txt b/man/aeroup.man.txt index 90debf1..be4a7a0 100644 --- a/man/aeroup.man.txt +++ b/man/aeroup.man.txt @@ -1,139 +1,109 @@ -man(1) AeroUp man page man(1) - - +man(1) AeroUp man page man(1) NAME AeroUp - SYNOPSIS - aeroup [-t serialPort] [-o serialPort] [-c red,green,blue,serialPort] [-G - serialPort] [-S serialNumber,serialPort] [-i gloFile] [-u gloFile,serialPort] - [-k serialPort] [-U glocFile,serialPort] [-P] [-v] [-h] - - + aeroup [-t serialPort] [-o serialPort] [-c red,green,blue,serialPort] [-G serial‐ + Port] [-S serialNumber,serialPort] [-i gloFile] [-u gloFile,serialPort] [-k serial‐ + Port] [-U glocFile,serialPort] [-P] [-v] [-h] DESCRIPTION - AeroUp is an open source command line tool to control Ultimate (programmable - light sequencing juggling props) from Aerotech Projects. - + AeroUp is an open source command line tool to control Ultimate (programmable light + sequencing juggling props) from Aerotech Projects. OPTIONS -t, --test=serialPort Send a test command on dev serialPort. - -o, --start=serialPort Send a start sequence command on dev serialPort. - -c, --color=red,green,blue,serialPort Send a color command on dev serialPort. Colors red, green, blue can be hexadecimal or decimal value in range of [0-255] hex value have to begin with 0x. - -G, --getSerial=serialPort get serial number on dev serialPort, and print it to standard output. - - -S, --setSerial=serialNumber,serialPort Set serialNumber on dev serialPort. 32 bits value can be writen in hexadecimal (0x#) or decimal (#). - -i, --verify=gloFile Verify that syntax glo file is valid - -u, --uploadGlo=gloFile,serialPort - Verify that syntax glo file is valid and if this is the case upload it - on dev serialPort - - + Verify that syntax glo file is valid and if this is the case upload it on dev + serialPort -k --symlink=serialPort return the serial name used as symlink of kernel name by udev (work with linux only). see the improved management driver section below. But you can also use this command to retrieve an more readable id than serial number. - Improved management driver (linux only) - note: you may need to update to last bootloader (aeroup was tested - with Club_Ball_Poi_V2.3.hex). you 'll find it on the Aerotech ltd web - page. - - To use the system management driver, you first need to set the apropri‐ - ate serial number in your props with the --setSerial option. (See the - address table belowx). And put the file aeroup.rule to your udev rules - directory if it wasn't done during installation. When you plug your - props you should now have a corresponding symlink to your /dev direc‐ - tory. - - ================================================ - Props | Range adress | id char | Symlinks - ================================================ - Ball | 0.0.98.0/24 | b | /dev/Ball# - Staff | 0.0.115.0/24 | s | /dev/Staff# - Club | 0.0.99.0/24 | c | /dev/Club# - Poi | 0:0:112:0/24 | p | /Poi/Poi# - ================================================ - - + note: you may need to update to last bootloader (aeroup was tested with + Club_Ball_Poi_V2.3.hex). you 'll find it on the Aerotech ltd web page. + + To use the system management driver, you first need to set the apropriate se‐ + rial number in your props with the --setSerial option. (See the address table + belowx). And put the file aeroup.rule to your udev rules directory if it + wasn't done during installation. When you plug your props you should now + have a corresponding symlink to your /dev directory. + + ================================================== + Props | Range adress | id char | Symlinks + ================================================== + Ball | 0.0.98.0/24 | b (0x62) | /dev/Ball# + Staff | 0.0.115.0/24 | s (0x73) | /dev/Staff# + Club | 0.0.99.0/24 | c (0x63) | /dev/Club# + Poi | 0:0:112:0/24 | p (0x70) | /Poi/Poi# + ================================================== -P, --thread Multithread mode, not implemented yet... - -U, --uploadGloc=glocFile,serialPort not implemented yet... - -v Verbose mode - -h, --help Print help - --version Print version The last bootloader V2.3 from Aerotech needs to be installed first to use Serial number features. Each sub options have to be separate with a comma without blank. - - EXAMPLES + # Test prop on /dev/ttyACM0 aeroup -t /dev/ttyACM0 + # Start props on /dev/ttyACM0 et /dev/tty/ACM1 and test /dev/tty/ACM3 aeroup -o /dev/ttyACM0 -o /dev/ttyACM1 -t /dev/ttyACM3 - aeroup -c 255,69,255,/dev/ttyACM0 27,3,7,/dev/ttyACM1 - aeroup -S 0x0b01/dev/ttyACM0 + # Set color to blue and red + aeroup -c O,O,255,/dev/ttyACM0 255,0,0,/dev/ttyACM1 + # Upload file.glo to /devttyACMO + aeroup -u /path/to/file.glo,/dev/ttyACM0 + # Set serial number 0x7002 to have a prop named Poi2 + aeroup -S 0x7002,/dev/ttyACM0 + # Verify your serial number is now : 0x7002 aeroup -G /dev/ttyACM0 - - + # Verify your serial name is Poi2 + aeroup -k /dev/ttyACM0 SEE ALSO - AeroUp project page : https://github.com/LaurentBa/AeroUp - AeroWrite project page : https://github.com/LaurentBa/AeroWrite + AeroUp project page : https://git.larueluberlu.net/AeroUp AUTHOR - Written by Laurent Barattero (laurent@larueluberlu.net.in) - + Written by Laurent Barattero (laurent@larueluberlu.net) COPYRIGHT - Copyright © 2013 BARATTERO Laurent License GPLv3+: GNU GPL version 3 or later + Copyright © 2013 BARATTERO Laurent License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>. - This is free software: you are free to change and redistribute it. There is - NO WARRANTY, to the extent permitted by law. - - - - - - - - - + This is free software: you are free to change and redistribute it. There is NO + WARRANTY, to the extent permitted by law. -0.8 December 2013 man(1) +0.8 December 2013 man(1) |